November 21, 2024

TROUBLESHOOTING SUPPORT

TROUBLESHOOTING SUPPORT

TROUBLESHOOTING VIDEOS

Check Control Transformer on an L&L Automatic Kiln (Video)
qr code

See https://www.youtube.com/video/Z8WCjC1IPwk?ecver=2

How to check the operation of a control transfomer on an L&L automatic kiln. Applies to all automatic kilns that are not 480 volts. The control transformer reduces the incoming line voltage from 240, 208 or 220 volts to 24 volts for the control and 12 volts for the relays.

Parts
  • See this page for 12 KVA control transformers used on kilns with three sections or less.
  • See this page for 30 KVA control transformers used on kilns with four or more sections.

    • TROUBLESHOOTING PDFS

    General L&L Kiln Troubleshooting Guide
    General troubleshooting tips for kilns.
    Basic Electricity Troubleshooting for L&L Kilns
    Electrical background information and troubleshooting tips for kilns.
    Element Troubleshooting & Installation Instructions
    Element troubleshooting and installation tips for kilns.
    Troubleshooting and Fixing Brick Problems
    Brick troubleshooting tips for kilns.

    TROUBLESHOOTING KNOWLEDGEBASE

    Adjusting Thermocouples

    For ideal firing results, thermocouples in each zone should be close regarding how far they

    Adjusting Thermocouples

    For ideal firing results, thermocouples in each zone should be close regarding how far they

    At what temperature should you turn off the Vent-Sure kiln vent?

    What is the recommended temperature to turn off the Vent-Sure kiln vent when firing glazes,

    Can I convert a manual J230 to an automatic JD230 and if so what do I need to get?

    It is possible to convert a J230 manual kiln into a JD230 automatic kiln. 

    What Parts
    Can I cool my kiln faster than it would normally?

    This question gets asked a lot around the holidays. L&L's official line on cooling the kiln

    Can I put Small Elements in an Element Channel designed for Large Elements?

    Yes - there is no problem putting a smaller element in a larger holder. Just be careful on the

    Can you use Advancer Shelves in an L&L Kiln?

    Question: I have several e28-T-3 kilns. I'm considering buying the Advancer kiln shelves made for

    Changing from 208 volts to 240 volts - what to do?
  • All the elements will need to be replaced.  Why?  For example, the ohms on the
    • Cone Offset
    CONE OFFSET - GENESIS

     

  • Turn kiln ON with toggle switch
    • Control reads higher temperature than my studio. No error code. What is wrong?

    The temperature on the display is saying 121F. It's not 121 in the studio. An independent

    Control reads higher temperature than my studio. No error code. What is wrong?

    The temperature on the display is saying 121F. It's not 121 in the studio. An independent

    Display Reads 2400 or CPLt When it Starts Up

    Even though you know the kiln is not that hot: this indicates a thermocouple failure.

    Does my Vent Motor require lubrication?
  • Before you purchase oil, check to be sure that you do not have a motor with sealed bearings.<
    • Does the Bartlett overtemperature control have a reset button like a "normal" overtemperature control?
  • If the controller is in the limit state (i.e. LMT flashing in the display), you must use the
    • Does the digital controller have a way to prevent an over fire?

    Once the kiln is properly calibrated after the test firing, it will fire very reliably for many

    Does the digital controller have a way to prevent an over fire?

    Once the kiln is properly calibrated after the test firing, it will fire very reliably for many

    DynaTrol Programs in Excel Format

    E-4, E- 4, or Err4 error code
  • Specifically this error code means that during a cooling segment in the programmed firing,
    • Electrical Supply Problems and slow kiln performance

    One of the most difficult kiln performance problems to address is a problem with the electrical

    Electrical Supply Problems and slow kiln performance

    One of the most difficult kiln performance problems to address is a problem with the electrical

    Element Connections are glowing. Why? What should be done?
  • An element connection can begin to glow if it is overheating. There are a few ways this can
    • Element Connections are glowing. Why? What should be done?
  • An element connection can begin to glow if it is overheating. There are a few ways this can
    • Error Codes for the One-Touch Control
    tC FAIL tC alternating with FAIL

    Indicates the thermocouple has failed. Replace the defective

    Genesis Control will not connect with WIFI
    The few things to check

    Using the WiFi opens up new possibilities with the Genesis controller.

    How can I extend ceramic kiln element life?
    Why do elements in electric kilns fail? How can you save on kiln maintenance costs?

     <

    How can I extend ceramic kiln element life?
    Why do elements in electric kilns fail? How can you save on kiln maintenance costs?

     <

    How can I protect an existing power supply?
    Circuit Breakers
  • Circuit breakers that have tripped and have been reset continually will
    • How can I tell the difference between elements wired in parallel versus series in my Jupiter, DaVinci, or Doll kiln?
  • Your Jupiter, DaVinci, or Doll kiln will have its elements either wired in parallel or wired
    • How can my kiln section stay on all the time in my computerized kiln, even when the on/off switch is off?
    A Relay May Be Stuck Shut
  • All computerized kilns use relays to cycle the power on and off
    • How can my kiln section stay on all the time on my manual kiln even when the kiln-sitter is off?

    Usually, this means a relay is stuck and needs to be replaced.

  • On 3-phase kilns,
    • How can the thermocouple wires get reversed on a Jupiter or DaVinci Automatic Kiln?

    When packed, the thermocouples on the Jupiter JD and DaVinci kilns are mounted to the kiln

    How deep should a Kiln Sitter Tube go into a kiln? How do you adjust the depth?
  • The Kiln Sitter Tube assembly should stick into the kiln about 1". This will allow air to
    • How do hold times and heatwork affect my work?
  • There is an option to add time to the end of the program when you enter a program. Usually,
    • How do hold times and heatwork affect my work?
  • There is an option to add time to the end of the program when you enter a program. Usually,
    • How do hold times and heatwork affect my work?
  • There is an option to add time to the end of the program when you enter a program. Usually,
    • How do I adjust my kiln-sitter?
    When to inspect the kiln sitter
  • Kiln-sitters need to be adjusted and inspected before the
    • How do I control my vent fan motor with my Genesis or DynaTrol?
    See the Vent-Control Option.
    How do I control the cooling with the DynaTrol?

    There are three different ways to control the cooling rate on the DynaTrol.

    Method A

    How do I enter a really slow program?

    On the DynaTrol you will need to use the Vary-Fire programming. On a Genesis use the Custom

    How do I enter a really slow program?

    On the DynaTrol you will need to use the Vary-Fire programming. On a Genesis use the Custom

    How do I fire with fewer kiln sections on my Jupiter Kiln?

    The outlets are numbered on the side of the control box. In this example below all the outlets

    How do I fire with fewer sections on my five section kiln?
  • Remove the lid. Open it first to remove the spring-loaded connections to the front of the lid
    • How do I fix pinholes and blistering in glazing?
  • The first thing to check is to make sure you are not putting on too thick a layer of glaze.<
    • How do I fix pinholes and blistering in glazing?
  • The first thing to check is to make sure you are not putting on too thick a layer of glaze.<
    • How do I hook up my kiln to power?

    L&L's official recommendation is for an electrician to connect the kiln to power. You should

    How do I keep elements from falling out of the element holders in the corner of a kiln?
  • Sometimes with thick elements, especially in the corner of a DaVinci, or Easy-Load kiln, the
    • How do I keep elements from falling out of the element holders in the corner of a kiln?
  • Sometimes with thick elements, especially in the corner of a DaVinci, or Easy-Load kiln, the
    • How do I keep elements from falling out of the element holders in the corner of a kiln?
  • Sometimes with thick elements, especially in the corner of a DaVinci, or Easy-Load kiln, the
    • How do I keep elements from falling out of the element holders in the corner of a kiln?
  • Sometimes with thick elements, especially in the corner of a DaVinci, or Easy-Load kiln, the
    • How do I know if my vent is pulling enough air through?
  • We recommend that you have a carbon monoxide monitor installed in your kiln room to